Call Today

 

They are making several great points on Tools You Need to Install a New Bathtub overall in the content followed below.

Installing a bathtub isn't precisely rocket science, yet it does require solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old bathtub with a new one is also a reasonably tough task. If the old tub is easily available, the task can relocate immediately; if you have to open a wall to eliminate the old tub and position the new bathtub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will certainly need an assistant to vacate the old tub and embeded in the new one. See to it you have qualified yourself for the work and are comfortable trying it. Instead of employing a specialist to take control of a halfway-completed task, it is much better to think about employing one prior to you begin. Opportunities are you may need a professional plumber to make tube links.
This post will certainly aid you set up a new bathtub in your shower room if you have currently purchased a brand-new tub and do not require to transform the plan of your previous water supply pipes.
Your devices as well as product list must comprise the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you require to replace old faucets with new ones as a part of your installation, then the first thing you must do is disconnect the water. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing taps can be fairly bothersome because of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipes. When the supply pipelines have been eliminated, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing compound.
Before carrying on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will certainly need a plastic connector to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin making sure that the washing machines are in area between the faucet and also the sink. Protect the tap in place with the supplier supplied backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The previous type must be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.

 

 

Installing the Bath tub

Utilizing the two wood boards under its feet, put the bath tub in the called for setting. The wood boards are valuable in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub until the spirit level checks out level.
To install taps, fit the bottom of the outermost flexible tap adapter to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Switch on the supply of water and examine all joints and new pipework for leakages as well as tighten them if required. Load the bathtub as well as also check the overflow electrical outlet and the regular outlet for leaks.
Ultimately, repair the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the bathtub should wait up until the bathtub has been utilized at the very least once as this will certainly settle it right into its final position.

 

 

Getting ready for the Installation

Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to prevent strain on the bath tub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you make use of all of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last position.

 

 

Tiling Around the Tub

In the location where the bath meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a stiff seal, causing the water to pass through the wall surface between the bath as well as the tiling, resulting in issues with wetness as well as possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and also are capable of securing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched paper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to permit the motion experienced when the tub is in usage. The sealer can fracture relatively very early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily available on the market. It is suggested to fit the floor tiles utilizing water-resistant or water resistant glue and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Hopefully you liked our article about Installing A Bathtub. Thanks for finding the time to browse our piece. Are you aware of somebody who is fascinated about Tools You Need to Install a New Bathtub ? Be sure promote it. We love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Top service, dial!